Wilson W500 54" Magnet Mount CB & Amateur Antenna 10 &11 Meter

Description: Details The Wilson 500's higher gain performance for an economical antenna is the result of several design modifications to the famous Wilson 1000. Using the basic design of the W-1000, Wilson is able to produce a mid priced magnetic antenna with great performance characteristics. This produced the most powerful CB base loaded antenna available in its price range. A large portion of the power that goes into a typical base loaded CB antenna is lost as heat in the coil and as dielectric heat loss in the plastic inside the coil form. Many CB antennas lose more than 50% of the power put into them. The power is wasted as heat loss and not radiated as radio waves. Another weak link in other CB antennas is the capacitor used to match the coax to the antenna, which is a cheap and easy way to make the SWR look good, but has lots of power loss, plus blows out when high power is applied to it. Wilson's first priority was to reduce the dielectric loss by removing as much of the plastic inside the coil as possible. This was accomplished by suspending the coil in air, supported only at four small points, 90 degrees apart, in effect removing 95% of the plastic from the inside surface of the coil. This reduced the dielectric loss to a negligible amount. The second priority was to get rid of the resistive heat losses in the coil. Since most of the RF energy at 27 MHz travels on the surface of the wire, it was decided to increase the surface area by making the diameter of the wire 12 gauge copper. Finally, to get rid of the losses in the matching between the coax and the loading coil, the lossy capacitor was eliminated and a more difficult but more efficient means of coupling the antenna was used. A Scalar Network Analyzer was used to determine the very precise point to direct match the coil with the coax and obtain the best match with maximum power transfer. The combination of all these accumulated design points allows the W-500 to have a 2,000 watt power rating with a 20-25% increase in performance over the Little Wil. 2000 Watt power handling capability (ICAS)Made with high impact Mobay thermoplasticHeavy-duty coil uses 12 guage copper wireExclusive low loss coil design54" 17-7 PH stainless steel whipFrequency range 26 MHz to 30 MHzWeather channel ready2 Year limited warrantyBoxed RADIOS RADIO ACCESSORIES ANTENNAS ELECTRONICS AUTOMOTIVE Wilson W500 54" Magnet Mount CB & Amateur Antenna 10 &11 Meter Details The Wilson 500's higher gain performance for an economical antenna is the result of several design modifications to the famous Wilson 1000. Using the basic design of the W-1000, Wilson is able to produce a mid priced magnetic antenna with great performance characteristics. This produced the most powerful CB base loaded antenna available in its price range. A large portion of the power that goes into a typical base loaded CB antenna is lost as heat in the coil and as dielectric heat loss in the plastic inside the coil form. Many CB antennas lose more than 50% of the power put into them. The power is wasted as heat loss and not radiated as radio waves. Another weak link in other CB antennas is the capacitor used to match the coax to the antenna, which is a cheap and easy way to make the SWR look good, but has lots of power loss, plus blows out when high power is applied to it. Wilson's first priority was to reduce the dielectric loss by removing as much of the plastic inside the coil as possible. This was accomplished by suspending the coil in air, supported only at four small points, 90 degrees apart, in effect removing 95% of the plastic from the inside surface of the coil. This reduced the dielectric loss to a negligible amount. The second priority was to get rid of the resistive heat losses in the coil. Since most of the RF energy at 27 MHz travels on the surface of the wire, it was decided to increase the surface area by making the diameter of the wire 12 gauge copper. Finally, to get rid of the losses in the matching between the coax and the loading coil, the lossy capacitor was eliminated and a more difficult but more efficient means of coupling the antenna was used. A Scalar Network Analyzer was used to determine the very precise point to direct match the coil with the coax and obtain the best match with maximum power transfer. The combination of all these accumulated design points allows the W-500 to have a 2,000 watt power rating with a 20-25% increase in performance over the Little Wil. 2000 Watt power handling capability (ICAS)Made with high impact Mobay thermoplasticHeavy-duty coil uses 12 guage copper wireExclusive low loss coil design54" 17-7 PH stainless steel whipFrequency range 26 MHz to 30 MHzWeather channel ready2 Year limited warrantyBoxed Details The Wilson 500's higher gain performance for an economical antenna is the result of several design modifications to the famous Wilson 1000. Using the basic design of the W-1000, Wilson is able to produce a mid priced magnetic antenna with great performance characteristics. This produced the most powerful CB base loaded antenna available in its price range.A large portion of the power that goes into a typical base loaded CB antenna is lost as heat in the coil and as dielectric heat loss in the plastic inside the coil form. Many CB antennas lose more than 50% of the power put into them. The power is wasted as heat loss and not radiated as radio waves. Another weak link in other CB antennas is the capacitor used to match the coax to the antenna, which is a cheap and easy way to make the SWR look good, but has lots of power loss, plus blows out when high power is applied to it.Wilson's first priority was to reduce the dielectric loss by removing as much of the plastic inside the coil as possible. This was accomplished by suspending the coil in air, supported only at four small points, 90 degrees apart, in effect removing 95% of the plastic from the inside surface of the coil. This reduced the dielectric loss to a negligible amount.The second priority was to get rid of the resistive heat losses in the coil. Since most of the RF energy at 27 MHz travels on the surface of the wire, it was decided to increase the surface area by making the diameter of the wire 12 gauge copper.Finally, to get rid of the losses in the matching between the coax and the loading coil, the lossy capacitor was eliminated and a more difficult but more efficient means of coupling the antenna was used. A Scalar Network Analyzer was used to determine the very precise point to direct match the coil with the coax and obtain the best match with maximum power transfer. The combination of all these accumulated design points allows the W-500 to have a 2,000 watt power rating with a 20-25% increase in performance over the Little Wil.

Price: 116.5 USD

Location: Niles, Michigan

End Time: 2024-02-15T10:06:56.000Z

Shipping Cost: 0 USD