Waveshare 320×480 3.5inch TFT LCD Resistive Touch Display SPI for Raspberry Pi

Description: This auction is for 3.5inch RPi LCD (A) 480x320, 3.5 inch Touch Screen TFT LCD Designed for Raspberry Pi Features 480x320 hardware resolution Resistive touch control Supports any revision of Raspberry Pi (directly-pluggable) Drivers provided (works with your own Raspbian/Ubuntu/Kali) Supports FBCP software driver as well, allows to config software resolution and set up dual-display Size perfectly fits the Pi (Raspberry Pi B+/2B/3B/3B+) High quality immersion gold surface plating Combined with the Raspberry Pi, allows you to: Take photos by touching (up to 17 camera modes) Use software keyboard (system interaction without keyboard/mouse) 3.5inch RPi LCD (A) and 3.5inch RPi LCD (B) are hardware compatible with each other (uses different driver), and can be mutually substituted in most cases. (A) for low cost ver. while (B) for IPS ver. with better displaying. Key Parameters LCD Type TFT LCD Interface SPI Touch Screen Type Resistive Touch Screen Controller XPT2046 Colors 65536 Backlight LED Resolution 320*480 (Pixel) Aspect Ratio 8:5 Power Consumption TBD Backlight Current TBD Operating Temp. (℃) TBD Photos Interface PIN NO. SYMBOL DESCRIPTION 1, 17 3.3V Power positive (3.3V power input) 2, 4 5V Power positive (5V power input) 3, 5, 7, 8, 10, 12, 13, 15, 16 NC NC 6, 9, 14, 20, 25 GND Ground 11 TP_IRQ Touch Panel interrupt, low level while the Touch Panel detects touching 18 LCD_RS Instruction/Data Register selection 19 LCD_SI / TP_SI SPI data input of LCD/Touch Panel 21 TP_SO SPI data output of Touch Panel 22 RST Reset 23 LCD_SCK / TP_SCK SPI clock of LCD/Touch Panel 24 LCD_CS LCD chip selection, low active 26 TP_CS Touch Panel chip selection, low active External Dimension Development Resources Wiki : www.waveshare.com/wiki/3.5inch_RPi_LCD_(A) FAQ Why the LCD doesn't work with my Raspbian?To use the LCD with the Raspberry Pi official image, driver should be installed first. Please refer to the user manual. However, for the first testing, you may want to use our provided image directly.Why the LCD still doesn't work with the Waveshare provided image?Make sure the hardware connection is correct and connects fine. Make sure the image in TF card is burnt correctly. The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the TF card was in bad contact.Which power supply should I use?It is recommended to use a 5V/3A power adapter for the Raspberry Pi other than USB connection, otherwise the Pi may failed to start up because the PC's USB port might have not enough power. For large size LCDs, say, 10inch diagonal or more, another stand-alone power adapter is also required to provide power to the LCD. For more info, please check the wiki page. Anti-Piracy CAUTION: This product is protected by patent, anyone making copies/knock-offs SHOULD be held liable pursuant to law. Since the first-generation Raspberry Pi released, Waveshare has been working on designing, developing, and producing various fantastic touch LCDs for the Pi. Unfortunately, there are quite a few pirated/knock-off products in the market. They're usually some poor copies of our early hardware revisions, and comes with none support service. To avoid becoming a victim of pirated products, please pay attention to the following features when purchasing: (Click to enlarge) Package Contains 3.5inch RPi LCD (A) x 1 Touch pen x 1 RPi screws pack (2pcs) x 1 Quick start sheet x1 1 2 3 4

Price: 24.63 USD

Location: Shenzhen, Guangdong

End Time: 2024-02-29T11:41:06.000Z

Shipping Cost: 0 USD