Very Loud Piezo Alarm Siren 2 Unique Sounds Dual Trigger 2 Zone Inputs 6VDC 12V

Description: Attractive Dual Mode Piezo Alarm Security Alarm Box Opened to Pre-Test Alarm before Shipping One of my customers tells me this alarm is compatible with the Titan XT and the Honeywell Security Alarms when connected to the HW1 terminals. However, since this is hearsay, you need to verify that your HW1 terminals output a 6 to 12 Volt DC Voltage. Dual Mode6 Volt DC Piezo Siren, or 12V DC 2 Operating ModesContinuous and Yelping ModesFor Yelping Mode, Read "Advisory" BelowModes Can Be Used Simulatneously (For Instance, Mode 1 for Front Door, Mode 2 for back Door)-Low Current Drain (55ma @ 6VDC)Current Drain @ 12VDC: 110ma-Easy Wiring with Screw Connections4 Mounting Screws Included4 Drywall Anchors Included Dimensions: 12cm x 8.3cm x 2.3cm-Internal Cover Activated Micro Switch with Screw Terminals(Normally Open Contacts, Can be wired in series with the Siren so it can be disabled when Siren's Cover is Opened)If planning to use the Yelping Mode, please make sure you read the "Advisory" below as it's operation is conditional !!! Both Operating Modes can simultaneously be wired to different external sensor switches so the Siren produces a unique sound for each sensor switch. For instance, Front Door and Back Door Sensors Switches can cause the siren to produce unique sounds, one yelping and the other continuous (when appropriately wired). Thus eliminating the need to have separate sirens for monitoring two different locations! (( PLEASE NOTE )) This is just the Siren. You still need an external sensor switch and a 6V DC Power Source connected to it to complete the circuit. Or, you need a "6V DC" Alarm Output on an existing security system for connection to it. If purchasing this siren, Please Print This Ad, or Paste it into Notepad and save it as a text file. It Contains Hook-Up Information that will be helpful to you when you install the siren! Wiring: Continuous Mode Wiring: Connect 6V DC to Gnd and #1 Terminal Yelping Mode Wiring: Connect 6V DC to Gnd and #2 TerminalIf the Siren sounds continuously at 6 Volt,you may need to insert a diode in serieswith the positive lead (diode included).Since diodes are polarity sensitive, thebanded end of the diode needs to connectto the #2 terminal. Siren Continuous Mode seems to work fine on voltages up to a maximum of 12V DC ADVISORY: With a switch closure across the Gnd and #2 terminals and the alarm being powered by a 6V DC source, the Siren operates in the "Yelping" mode. If more than 6V DC is used to power the alarm, the above switch closure will Operate the Siren in Continuous Mode producing the same sound as a Switch Closure across the Gnd and #1 Terminals. The box does not state the alarm's "db" rating. I would estimate the "db" rating to be about 95 db, give or take about 5 db. Though not as loud as some alarms I sell, the "Yelping" mode produces a very unique distinctive sound that helps extend it's range and coverage area beyond that of similar alarms. Attention: The Box Reads: 15 Watt I have seen time and time again that the claims by Chinese manufacturer's are false and I have learned not to trust them. So, I measured the current drawn by this device at both 6V DC and 12V DC operation. As I suspected, the manufacturer's claim that this is a 15W device was false. My current measurement of 110ma current draw when operated at 12V DC only works out to 1.32 Watts. This 9-Piece Lot Includes: 1 Alarm as shown 4 Mounting Screws 4 Drywall Anchors

Price: 7.99 USD

Location: Burton, Michigan

End Time: 2024-08-17T03:00:18.000Z

Shipping Cost: N/A USD