USB3.0 9mp imx533 1inch CMOS sensor astronomical telescope cool astronomy camera

Description: USB3.0 9mp SONY imx533 1inch CMOS sensor astronomical telescope cool astronomy camera with TE cooling temperature control NOTE: Color Camera's protect window default installed IR cut filter RisingCam can change IR-Cut filter or AR protective glass for buyer before shipping buyer just can select only one, if installed can not change again: (1) IR-Cut Filter (Spectral Range 380-690nm) (2) double-side AR coating Protective glass (Spectral Range 350-1050nm) buyer should select IR cut filter or AR protective glass when place order Camera Description Feature Standard M42 Mount camera with SONY imx533 1inch CMOS sensor, Color Sensor Sensor Resolution: 9MP Image bits depth: 8/14bits Two-stage TE-cooling (Thermo Electric Cool)temperature controllable with electric fan; Bulit-in Dew heater Desiccant bulit-in inside Camera Back Focus distance: 17.5mm Two-stage TE-cooling (Thermo Electric Cool)temperature controllable with electric fan Sensor cooling can be 40 degree below ambient temperature Note: -35°C below ambient under short exposure/ -40°C under long exposure time(> 1s) Working temperature can be regulated to specified temperature in 5 minutes High sensitivity: 485mv with 1/30s 0.07mv with 1/30s Smart structure to assure the heat radiation efficiency and avoid the moisture problem IR-CUT filter (AR coated windows for Optional) Up to 1 hour long time exposure; USB3.0 5Gbit/second interface ensuring high speed data transmission Ultra-FineTM color engine with perfect color reproduction capability With advanced video and image processing application RisingSky Support both video and trigger modes Providing Windows/Linux/Mac OS multiple platforms SDK Native C/C++, C#/VB.NET, DirectShow, Twain control API The ATR3 CMOScan be widely used in low light environment image capture and analysis, astronomy deep sky application. Instruction ATR3 CMOS 9MP camera adopts SONY 1" CMOS sensor as the image-picking device and USB3.0 is used as the transfer interface to increase the frame rate. With the two-stage peltier cooling sensor chip to -42 degree below ambient temperature. This will greatly increase the signal to noise ratio and decrease the image noise. Smart structure is designed to assure the heat radiation efficiency and avoid the moisture problem. Electric fan is used to increase the heat radiation speed. USB3.0 is used as the data transfer interface to increase the frame rate. ATR3 CMOS 16mp camera comes with advanced video & image processing application RisingSky; Providing Windows/Linux/OSX multiple platform SDK; Native C/C++, C#/VB.NET, DirectShow, Twain Control API; The ATR3 Camera can be widely used in low light environment image capture and analysis, astronomy deep sky application. Camera Specification Sensor Sony IMX533 back illuminated sensor Diagonal 15.968 mm Image Resolution 9.07 mega pixels(3008*3000) Pixel Size 3.76mm ´3.76mm Image Area 11.31mm ´11.28mm Max FPS at Resolution (USB 3.0) 14bit 8bit 20 FPS @ 3008*3000 62 FPS @ 1488*1500 186 FPS @ 992*998 40 FPS @ 3008*3000 62 FPS @ 1488*1500 186 FPS @ 992*998 Max FPS at Resolution (USB 2.0) 14bit 8bit 1.7 FPS @ 3008*3000 6.6 FPS @ 1488*1500 15.5 FPS @ 992*998 3.3 FPS @ 3008*3000 13.1 FPS @ 1488*1500 31 FPS @ 992*998 Max FPS at Resolution (Low Noise, USB 3.0) 14bit 8bit 13.3 FPS @ 3008*3000 (Low Noise Modeis only available in All Pixel Readout Mode) 27.5 FPS @ 3008*3000 (Low Noise Modeis only available in All Pixel Readout Mode) Max FPS at Resolution (Low Noise, USB 2.0) 14bit 8bit 1.7 FPS @ 3008*3000 (Low Noise Modeis only available in All Pixel Readout Mode) 3.3 FPS @ 3008*3000 (Low Noise Modeis only available in All Pixel Readout Mode) Shutter Type Rolling shutter Exposure Time 0.1ms – 3600s Gain 1x – 100x SNR 47 dB Dynamic Range 87 dB (Low Noise Mode) Read Noise 2.25 – 0.94 e- Read Noise (Low Noise Mode) 1.42 – 0.97 e- QE Peak >80% Full Well 50ke- ADC 14bit DDR3 Buffer 512MB (4Gb) Connection Port USB3.0/USB2.0 Camera Adaptor M42 x 0.75mm Protect Windows IR-cut filter/AR-window Spectral Range 380-690nm (with IR-cut filter) Capture/Control SDK Windows/Linux/macOS/Android Multiple Platform SDK(Native C/C++, C#/VB.NET, Python, Java, DirectShow, Twain, etc.); Recording System Still picture and movie Camera Dimensions Diameter 80mm * height 103mm Camera Weight 0.552kg Back Focus Distance 17.5mm Cooling: Two stage TEC Effective Cooling Temp: -35°C below ambient under short exposure/ -40°C under long exposure(> 1s) Supported OS Microsoft®Windows® XP / Vista / 7 / 8 /10 (32 & 64 bit) OSx(Mac OS X) Linux Camera Pictures Sony IMX533 sensor Sensitivity The sensor G sensitivity of ATR3CMOS09000KPA is 535mv with 1/30s. Its spectral sensitivity is shown in Figure 2. Camera install SONY imx533 CMOS sensor Sensor size: 1 inch, Resolution: 9mp Frame rate: 20fps/3008x3000(14bit) 40fps/3008x3000(8bit) 62fps/1488x1500 186fps992x998 IMX533 Spectral Sensitivity Characteristic 14bit ADC and ROI The ATR3CMOS09000KPA has built in 14bit ADC. It also has 12bit output mode for hardware binning and smaller resolution. The camera also supports hardware ROI, and the smaller the ROI size is, the higher the frame rate is.Table 2 shows the frame rate of the ATR3CMOS09000KPA in 14/8bit mode, USB3.0 / USB2.0 data transfer interface at different resolutions:Table 2 ATR3CMOS09000KPA Frame Rate at Different Resolution/Data Bit/Data Transfer(USB3.0/ USB2.0) Bit & Interface FPS Resolution 14bit ADC 8bit ADC USB3.0 USB2.0 USB 3.0 USB 2.0 3008 * 3000 20 1.7 40 3.3 3008 * 3000 (Low Noise) 13.3 1.7 27.5 3.3 1488*1500 62.0 6.6 62.0 13.1 992*998 186 15.5 186 31 DDR3 Buffer ATR3CMOS09000KPA camera has a 512MB (4Gb) DDR3 buffer, which helps maintain the stability of data transmission, and effectively reduce the amp-glow caused because image data can be temporarily buffered without being sent hastily to the receiver. Binning The ATR3CMOS09000KPA supports digital binning from 1´1 to 8´8 in either stacking or averaging method, and hardware binning from 1´1 to 3´3 in averaging method. Hardware pixel binning is much faster than software binning. Conversion Gain Switch ATR3CMOS09000KPA support HCG and LCG mode switch, the Gain ratio is 3.05. Power and Cooling System for Precise Temperature Regulation The Camera can be powered by DC12V 3A power source. Please remember that when the power adaptor is plugged in, cooling system and image process system are both powered by DC 12V port, otherwise, image process system is powered by USB port while cooling system is off.The cooling system of ATR3CMOS09000KPA is two-stage Thermoelectric Cooling (TEC) with controllable electric fan assisting heat dissipation.The TEC system is controlled by PID algorithm, which allows the TEC to be precisely regulated towards the target temperature with 0.1°C deviation.The working temperature can be regulated to specific number, and effective temperature drop can be -40°C from ambient temperature. Such efficient cooling system guarantees the stability of ultra-low noise mode and quality of the camera image. Zero Amp-Glow ATR3CMOS09000KPA has been carefully designed and is able to achieve zero amp-glow photo shooting. Figure 3 and Figure 4 show the different cameras at 20°C and 5-minute exposure time with and without amp-glow. By comparison, the image captured by ATR3CMOS09000KPA shows zero amp-glow. Camera setting used for performance analysis is shown below: Full resolutionl RAW 14-bit model Temperature: -10°C ASCOM/WDM (DirectShow)/Native driver/INDI for easy connection with 3rd party astrophotography softwares Supported Software for this camera includes: NINA, PHD Guiding, Nebulosity,MaxIm DL, SharpCap, MetaGuide,Fire Capture, Astro Art, Registax, AstroStack, DeepSky Stacker, Kstars etc Our this camera support INDI INDI is a protocol for the control of astronomical equipment. It is an open source project that aims to provide a unified control interface for various types and brands of astronomical equipment. StellarMate supports INDI protocol, so you can use it to control various devices connected to StellarMate. Our this camera support StellarMate StellarMate is an astronomy equipment management software. It provides an easy-to-use interface to control telescopes, cameras and other equipment from a computer or mobile device. With StellarMate, you can automate imaging, shot time tracking, metering and exposure timing without manual intervention. StellarMate also includes astronomical image processing tools to help you process and adjust your data after imaging. Our this camera support StellarMate X controller StellarMate X is a compact and powerful Astrophotography Controller that supports numerous Mounts, Cameras, and other astronomical equipment. Powered by Open Source technologies and designed and built by Astrophotographer for Astrophotographers. It provides unparalleled freedom in selecting your favorite platform to remotely control your equipment. You can use Ekos astrophotography tool on Windows, MacOS, or Linux. Furthermore, use StellarMate App on iOS and Android to automate your complete astrophotography workflow Two-stage TE-cooling (Thermo Electric Cool) The Camera can low down 40 centi-degree than ambient temperature, the Lowest target temperature is -30 centi-degree Darkfieldtestingfor the ATR3Camera at Gain 20 , Exposure 600 second, None Cool, hot noise image ATR3 Cameraat Gain 20 , Exposure600 second, Turn On Cooling, Minus 15 Centi-degree, hot nosie This camera bulit-in Dew heater inside of camera it can prevent Dew on inside of Camera's window The heating intensity can be adjusted in the RisingSky software And Desiccant bulit-in inside Camera too Camera Size Back focus distance: 17.5mm The ATR3CMOS body, made from tough, alloy with CNC technique, ensures a heavy duty, workhorse solution. The camera is designed with a high quality IR-CUT or AR to block the IR light or protect the camera sensor. The fan‘s vibration is minimized to the low level to eliminate the vibration caused imaging blur. This design ensures a rugged, robust solution with an increased lifespan when compared to the other industrial camera solutions. RisingTech Provide M42 to 1.25" adapter and M42 to 2" adapterfor buyers Our Camera also can be connect to Filter wheel RisingSky Software Instruction RisingSky is Professional software for Astronomical applications, which has multi-functions such as Camera parameter adjustment, capture images&video, modify image, process image etc. it can provide many tools choice for user. RisingSky Support Windows XP/7/8/10 system We also Provide RisingView software for MAC system and Linux system User. RisingSky for Windows system ATR3-16000KPA Long time exposure supported up to 3600s RisingView for MAC system RisingView for Linux system Astronomy Photo Sample Moon photo Nebula photo (Above 3 photo made bybuyer:Lorenzo Taltavull Menendez, who from Spain, thank you!!!) Camera Packing Standard Package 1- 3A safety equipment case: L:28cm W:23cm H:15cm (1pcs, 3.5Kg/ box); Single Camera net weight: 0.65kg carton size:L:28.2cm W:16.7cm H:25.5cm(TBD) 2- Power adapter: input: AC 100~240V 50Hz/60Hz, output: DC 12V 3A 3- ATR3CMOS camera(M42x0.75 Mount) 4- High-Speed USB3.0 A male to B male gold-plated connectors cable /1.5m 5- USB flash disk (RisingSky software+ASCOM driver+SDK) 6- M42 to 2inch adapter 7- M42 to 1.25inch adapter Gift 8- M42f-M42m_21mm extend adapter （Gift） 9- M42m-M48f_16.5mm extend adapter（Gift） 10- M48m-M42f adapter（Gift） 11- 12.5mm backfocus adapter（Gift） Warranty 1 year RisingCam will provide buyers with lifetime technical support to respond to buyers' technical questions If the camera has quality problems during the warranty period, RisingCam will provide technical support for buyers to solve problems If the camera needs to be returned to China for repair, RisingCam will repair it free. Out of warranty period, RisingCam will still provide buyers with technical support services and maintenance services

Price: 950 USD

Location: Hangzhou

End Time: 2025-01-21T04:17:27.000Z

Shipping Cost: 0 USD