Spicer 3-82-181 Driveshaft Yoke Shaft 1350 Series - 1.500x16 spline

Description: Spicer 3-82-181 Driveshaft Yoke Shaft 1350 Series - 1.500x16 spline - 6.812" Made in USA BrandSpicer Series1350 Outside Yoke Dimension (E) In.3.625 Bearing Cap Diameter (D) In.1.188 Major Spline Diameter1.500 Spline Count16 Involute SplineN Centerline To End Of Splne (K)6.812 End/Spline To Point/Rad. (R)4.688 Spline Length (L) In2.500 VMRS024002061 Angle #19.0 StyleSR Fast shipping from Florida Welcome to Mako Driveshafts LLCWe are excited to have you as our customersOur business is built around finding solutions for our customers and we appreciate every one of you!We are a proudly USA built company and we ship out of Fort Lauderdale, FloridaWhatever we have shown in stock is on the shelf and ready to shipWe offer same day shipping and if purchased before 1pm EST consider your order on the way! Type of U-Joint Common Series Slip Yokes Splines Center Bearings Flanges Weld Tube Yokes Step 1Establish what style of Universal Joint you are working with. This is important, since u-joints have a different way of measuring depending on the style of u-joint that you have. The way that you measure the u-joint will translate into how you measure the other components you may need. ALWAYS use a set of Vernier Calipers or Micrometers, tape measures will never produce accurate results! These are mechanical parts and require precision After comparing the Type of U-Joint in Step 1) Measure your u-joint in the correct manner and identify what series you haveOutside Snap Rings *Inside Snap Rings **Outside+Inside Snap Rings *** SPRTAB Style **** Bearing Plate *****Light & Medium Vehicles Outside Snap Rings *Inside Snap Rings **Outside+Inside Snap Rings *** SPRTAB Style **** Bearing Plate *****Commercial Vehicles There are two applications for slip yokes that determines what type of slip yoke you needTransmission slip yokes that slide onto the output shaft of your transmissionDriveshaft slip yokes that allow for the shaft to move in and out during operationPlease follow the stepsEstablish the type of universal jointMeasure and determine the series of your universal jointDetermine if you need a transmission or driveshaft slip yoke typeCount the splines and take note for missing splines. If you count 15 with a gap = 15/16OD, the outside diameter of the splined tubeMajor diameter which is used to ensure that the slip yoke and spline fit correctly There are two types of splines Determine if you need a regular stub shaft or a spline to be used with a center or carrier bearingDetermine the tube you are going to weld the butt end of the spline into (Outside diameter & Wall thickness)As a general rule, the (K) measurement of the spline should be about the length (CL) of the slip yokeMake sure that the spline major diameter & number of splined teeth matches that of your slip yoke Midship stub shaft (For use with Carrier Bearings) Center Bearing's are easy!They are used to support two piece driveshafts & are identified as follows:Compare the shape of the center bearing, do the brackets and general look of the bearing match?Take a measurement from the centerline of one mounting hole to the other to establish the lengthEnsure the inner diameter of our bearing matches the diameter of the spline its going onto Identify your FlangeFirst determine the type and series of the universal jointTake the measurement from the centerline of one bolt hole to the other on both sides of the flangeConfirm the flange pilot diameterAre the bolt holes drilled or threaded? Weld in Tube YokesFirst determine the type and series of your universal jointDetermine the outer diameter and wall thickness of your driveshaft tubingBeware of what material you are working with, aluminum tubing uses aluminum tube yokes

Price: 211 USD

Location: Fort Lauderdale, Florida

End Time: 2024-08-06T15:33:04.000Z

Shipping Cost: 0 USD