SEACHEM PHOSGUARD 100 ML BAG

Description: SEACHEM PHOSGUARD 100 ML BAG Product #: SEA-185 PhosGuard rapidly removes phosphate and silicate from marine and freshwater aquaria. It is not recommended for phosphate buffered freshwater. PhosGuard is highly porous for high capacity and bead-shaped for optimum water flow. Aluminum Oxide, Soluble Aluminum, and Coral Toxicity In recent years, there has been speculation that aluminum oxide based phosphate removers like PhosGuard release aluminum into the water and subsequently damage corals. The evidence to support this claim was largely anecdotal. So, through a series of controlled experiments in both freshwater and saltwater, we intended to address both the question of aluminum solubility and aluminum toxicity. The results of these experiments show that under reef conditions (pH near 8) there is no detectable soluble aluminum released from alumina. Under conditions of low pH and high dosage levels, soluble aluminum can be released from alumina; at three times the label dosage rate, we detected 0.2 mg/L aluminum at a pH of 5.3. Additionally, aluminum oxide is not easily absorbed into the cell to cause negative reactions. Even at three times the dose of PhosGuard, soft-bodied corals such as Sarcophyton remain unaffected. Directions May generate heat on initial contact with water. Pre-wet by adding to a double volume of freshwater, followed by a rinse. For best results, PhosGuard should be rinsed before use and placed so as to maximize the flow of water through it but not so that it tumbles against itself in flow. It may be used in a canister filter, media chamber, box filter, or any high flow area of a trickle filter. Use of a filter bag is recommended. Use 85 mL (1/3 cup) for every 200 L (50 US gallons) saltwater or 400 L (100 US gallons) freshwater. Leave product in place for 4 days, then test phosphate or silicate concentrations with either MultiTest: Phosphate or MultiTest: Silicate. If the concentration of the component you are trying to decrease has not dropped to around 0.02 mg/L, then replace the PhosGuard, otherwise leave in place until levels begin to climb again. As long as concentrations remain under control, the product is not exhausted. Over treating is not recommended. PhosGuard is not an exchange resin and does not release anything into the water. It does not leach phosphate or silicate back into the water and may be removed, dried, and returned to service until exhausted. Continuous use of small quantities is better than intermittent use of larger quantities. : How do I use PhosGuard? How long does it work and when is it exhausted? A: PhosGuard is best used in smaller quantities and changed frequently. In an environment with an excessively high phosphate reading, PhosGuard will exhaust rapidly (4 – 5 days). Place the product in a high flow rate area and test your phosphate levels, changing as needed. When you see that your level is below 0.2 ppm (mg/L) leave that portion of PhosGuard in the filter. PhosGuard may yellow somewhat as it picks up organics, but that is not an indicator of exhaustion for phosphate removal. Continue to test weekly for phosphate until you see it begin to rise again. You will then know that it is time to change the PhosGuard. If you have low levels of phosphate the PhosGuard will absorb the silicate in your system. It’s inert and safe to leave in your filter. Our Policies Payment Information IF YOU ARE BIDDING MORE THAN ONE ITEM - PLEASE WAIT AND PAY AFTER ALL AUCTIONS HAVE FINISHED. We will be happy to COMBINE SHIPPING on multiple purchases shipped in the same box. Combined Auctions / Store Purchases may not span more than 10 days. Please wait and send payment for all items together. Once you have paid for a purchase we can no longer add additional items to the box. Domestic and International Buyers We accept PAYPAL via eBay Checkout. Non-Paying Bidder will be reported after 10-15 days. If you need more time, please stay in touch or let us know you want to cancel and we will send you a cancel auction request. Shipping Info We ship UPS orders within 24 hours of cleared payment (Monday - Friday). USPS orders ship within 48 hours of cleared payment. To view shipping cost click on the Shipping & Payments tab and enter the quantity you are interested in. We ship out of our warehouse in Indianapolis, Indiana. All items listed on auction are physically in stock. We do have rare cases where inventory can be misplaced/lost in the warehouse, in these rare cases, we will contact you ASAP and offer your choice of a refund, alternative product, and/or ETA if you wanted to wait for the item. International Buyers are responsible for any taxes, duties, customs fees or additional charges incurred during shipping We ship USPS and UPS. We cannot ship gift or sample marked international packages or list a reduced value on the customs invoice. Please note electrical requirements for your countries electric grid. All products we sell, unless noted otherwise are 110v 60hz with a USA plug. Contact Us Store hours are 9:30 am - 6 pm Eastern time Monday through Friday. Feel free to call message us with product questions, recommendations and/or order status updates. Click here to visit our store

Price: 8.49 USD

Location: Indianapolis, Indiana

End Time: 2024-08-28T14:48:59.000Z

Shipping Cost: 0 USD