Rear End Overhaul Kit, 31 Spool Spline, Fits Ford 9 Inch

Description: Save time and money with a complete overhaul kit for your 9" Ford third member, This complete 9" Ford overhaul kit includes a full bearing set, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and Loctite, 28 spline version has LM501349 carrier bearings which are 1.625" ID and 2.879" OD, 31 spline version has LM102949 carrier bearings which are 1.781" ID and 2.879" OD, 31s version has LM603049 carrier bearings which are 1.781" ID and 3.063" OD as well as Daytona pinion bearing 9 Inch Ford Rear End Overhaul Kit, 31 Spline Sku # 9190950-31 Mfr. Part # 9190950-31 Condition New Brand Speedway Motors Sold Each Details Info This 9" Ford overhaul kit includes: pinion pilot, pinion shaft, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and Loctite. Ring gear bolts not included. NOTE: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings needed for use with our full spools. If you are using the H.D. nodular iron center section which uses the large diameter carrier bearings, order kit 9190950-31s, which also includes the large pinion bearings for use with the Daytona pinion support. - Double check your bearing p/n. 9190950-28 Includes carrier bearing # LM501349 28-spline axles DO NOT guarantee that the LM501349 bearings are used in the carrier. If in doubt, double check the bearings used and then order accordingly. 9190950-31 Includes carrier bearing # LM102949 31-spline axles DO NOT guarantee that the LM102949 bearings are used in the carrier. If in doubt, double check the bearings used and then order accordingly. 9190950-31S Carrier bearing # LM603049 (CONE) and LM603011 (CUP) TM88048 (CONE) Outer pinion bearing TM88010 (CUP) Large "Daytona " inner pinion bearing HM89443 (CONE) Race # HM89410 (CUP) LM603049 CONE ID: 1.781 " LM603011 CUP OD: 3.063 " TM88048 CONE ID: 1.308 " TM88010 CUP OD: 2.687 " HM89443 CONE ID: 1.308 " HM89410 CUP OD: 3.00 " Charts (GIF) Installation Tips 9190950-28Includes carrier bearing # LM50134928-spline axles DO NOT guarantee that the LM501349 bearings are used in the carrier. If in doubt, double check the bearings used and then order accordingly.9190950-31Includes carrier bearing # LM10294931-spline axles DO NOT guarantee that the LM102949 bearings are used in the carrier. If in doubt, double check the bearings used and then order accordingly.9190950-31SCarrier bearing # LM603049 (CONE) and LM603011 (CUP) TM88048 (CONE)Outer pinion bearing TM88010 (CUP)Large "Daytona" inner pinion bearing HM89443 (CONE)Race # HM89410 (CUP) LM603049 CONE ID: 1.781"LM603011 CUP OD: 3.063"TM88048 CONE ID: 1.308"TM88010 CUP OD: 2.687"HM89443 CONE ID: 1.308"HM89410 CUP OD: 3.00" Specs Sold in Quantity Kit MFG. Part # 9190950-31 Reviews Great overhaul kit! Everything you need! Rated by Colby G. on January 10, 2022 Summary: This fit perfectly and is installed, ready to crank up once the truck is finished! Yes, I recommend this product. good stuff. it all worked Rated by jeff on December 23, 2021 Summary: Worked as intended Cons: Did not contain the one roll main roll pin Pros: had the correct bearing for my job. Yes, I recommend this product. Everything seems ok. Rated by Eric on October 18, 2021 Summary: All the parts needed, except ring gear bolts, where included, and installed with no problems. Would buy again. Rated by Phil on October 01, 2021 Summary: All fit perfectly. Pros: Everything needed was included in kit Yes, I recommend this product. ford 9 in diff overhaul Rated by yvon on March 05, 2021 Summary: its too bad they have the solid spacer and shims and also crown bolts and washers in this kit . Yes, I recommend this product. Related Items / Suggested Parts 9 Inch Ford Solid Pinion Bearing Spacer Kit with Shims Pinion Nut for 9 Inch Ford 9 Inch Ford Gear Bearing Retaining Clip ARP 250-3003 Ford 8.8/9 Inch Ring Gear Bolts, 12 Point, Set/10 Motive Gear Ford 9 Inch Performance Ring and Pinion, 1957 - Up Style Ford 9 Inch Ring Gear Bolts, 7/16-20 x 1 Inch, Hex, Set/10 Third Member Mounting Hardware Kit, Ford 8 Inch/9 Inch Rearend Tech Support We're here to help before and after your purchase. If you have a question or need assistance with one of our products, please contact us through eBay Messaging and a knowledgeable Speedway Motors team member will be happy to help. About Speedway Motors is America’s Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 72 years. Founded in 1952 by “Speedy” Bill Smith – a racer and street rodder himself – Speedway has grown from a one-man operation to become the world’s largest manufacturer, distributor and retailer of street rod and racing products. Our industry-leading fast delivery is the result of same-day shipping from our state-of-the-art, centrally located 500,000 sq. ft. headquarters. Speedway’s size offers customers unmatched product selection and low pricing, while our excellent technical support and customer service have made us a recognized leader in the rodding and racing industries.

Price: 114.99 USD

Location: Lincoln, Nebraska

End Time: 2024-09-16T12:02:15.000Z

Shipping Cost: 0 USD