Neo Geo Sd Loader For Neo Geo Cd Top Loader Brand New

Description: neo geo SD LOADER FOR neo geo CD TOP LOADER BRAND NEWONLY USE FOR THE neo geo CD TOP LOADER Caution! NEOCD Kit FOR LA ONLY, console not included! Welding skill required! NEOCD (Rev M) with 64G TFCard for neogeo CD Console Top Loader STANDARD PACKAGES NEOCD Kit (Rev M Firmware V0.11) CD style TFCard adapter card 64G TF card (105 CD games and 8 cartridge games pre-installed) Installation of NEO-CDM3 boards: Using a soldering iron, heat PIN 12 for a few seconds and carefully lift it off the board with the needle. It shouldn't require much force. Don't pull too hard or you might rip the pad off the board. Bend the PIN back over the body of the chip. Avoid bending it back and forth repeatedly at all costs, as it will break easily. Insert the provided flex cable (20cm for charging plates) into the charging plate connector. Slide it with the blue tab facing up, the contacts facing down. Use your fingernail or a flathead screwdriver to help if needed, but be careful not to poke or cut through it. It should go in 2~3mm. Make sure it is straight. Solder the pad wire from the main board to pad A on the charger board. Solder the raised pin wire to pad B on the charger board. Make sure they are not swapped! Align the square charger connector at the top and press firmly in the center to snap the board onto the chip. It won't make a very audible click, but you should feel it lock into place. Make sure the board is firmly connected and parallel to the main board. Place the plastic spacer into the mounting bracket so that it presses onto the charger board where the 68000 chip sits when placed on top of it. Route the CDDA wires through the corresponding opening in the shield and connect the connector to the CDDA pins on the charger board in the correct way. The different colored cable (often white) should go on the side indicated by a small white arrow. Installation of NEO-CDM4 boards: Using a soldering iron, heat PIN 12 for a few seconds and carefully lift it off the board with the needle. It shouldn't require much force. Don't pull too hard or you might rip the pad off the board. Bend the PIN back over the body of the chip. Avoid bending it back and forth repeatedly at all costs, as it will break easily. Insert the provided flex cable (25cm for charging plates) into the charging plate connector. Slide it with the blue tab facing up, the contacts facing down. Use your fingernail or a flathead screwdriver to help if needed, but be careful not to poke or cut through it. It should go in 2~3mm. Make sure it is straight. Solder the pad wire from the main board to pad A on the charger board. Solder the raised pin wire to pad B on the charger board. Make sure they are not swapped! Align the square charger connector at the top and press firmly in the center to snap the board onto the chip. It won't make a very audible click, but you should feel it lock into place. Make sure the board is firmly connected and parallel to the main board. Route the CDDA wires through the corresponding opening in the shield and connect the connector to the CDDA pins on the charger board in the correct way. The different colored cable (often white) should go on the side indicated by a small white arrow. Installing TFCard Adapter Plate: Remove the CD drive and top case plate by removing the 8 screws as shown. Keep the 4 CD Drive flange screws aside. Lift both parts up, the CD drive may need a slight wiggle to slide off the plastic posts. Connect the end of the flex cable, blue tab facing up, contacts facing down. Use your fingernail or a flathead screwdriver to help if needed, but be careful not to poke or cut through it. It should go in 2~3mm. Make sure it is straight. VERSAND:Brief per Post, not normal 10 to 25th working stage world wide. EXPEDITION:Letter by ordinary courier, usually present 10 25 open days in the world. SHIPPING: Letter by ordinary mail, by myself from 10 am to 10 pm 25 giorni lavorativi in tutto il mondo. PAY: PAYPAL ALWAYS INDICATE THE NICKNAME FOR PAYMENTS BY TRANSFERPAYMENT:INTERNATIONAL SHIPPING ONLY FOR PAYMENTS BY PAYPAL NOTE:International Only for the purpose of PayPal payments PAYMENT:EXPEDITION INTERNATIONAL POUR ONLY PAYMENTS BY PAYPAL PAYMENT:SHIPPING INTERNATIONAL PER ONLY PAYMENTS WITH PAYPAL VOTING: The article will be voted on after receiving the vote, if there is any problem with the article DO NOT VOTE NEGATIVELY, let us know and we will resolve it amicably.VOTE:The article will be voted after receiving a vote, if there is any problem with the item NO NEGATIVE VOTE, let us know and we will solve it amicably. Absorption:The article after the end of one Abstention be carried out werden, wenn It's an urgent problem with the article number negatives Votum,that is some knowledge and we will lose it welcome. VOTE:The article will be I voted after having received a vote, Yes, there is already one problem with the element NO vote negative, We will know how and we all meet the solution to the friendly. VOTE: The article will be voted after having received a vote, if it is anyone problem with the voice of NO down vote, fatecelo know and We will solve it amichevally.Using a soldering iron, heat PIN 12 for a few seconds and carefully lift it off the board with the needle. It shouldn't require much force. Don't pull too hard or you might rip the pad off the board. Bend the PIN back over the body of the chip. Avoid bending it back and forth repeatedly at all costs, as it will break easily. Insert the provided flex cable (20cm for charging plates) into the charging plate connector. Slide it with the blue tab facing up, the contacts facing down. Use your fingernail or a flathead screwdriver to help if needed, but be careful not to poke or cut through it. It should go in 2~3mm. Make sure it is straight. Using a soldering iron, heat PIN 12 for a few seconds and carefully lift it off the board with the needle. It shouldn't require much force. Don't pull too h

Price: 115.63 USD

Location: Sant Boi de Llobregat

End Time: 2025-01-03T19:17:06.000Z

Shipping Cost: 17.87 USD