Kit Mini Reel Of Tesla 15–24 V Dc For Experiments High Voltage

Description: Kit Mini Reel Of Tesla 15–24 V Dc For Experiments High VoltageThe description of this item has been automatically translated. If you have any questions, please feel free to contact us. KIT Mini 15 – 24 V DC tesla coil for high voltage experiments PRODUCER: F.Elettronica REFERENCE: YB677 EAN CODE: This original kit allows you to create a mini Tesla coil which, by generating high voltage, creates a small lightning bolt which, for example, allows you to trigger a neon lamp by simply bringing it close to the coil.Attention, the product is a KIT and therefore you will receive the components to be welded with a soldering iron for electronics and everything needed to recreate the apparatus as shown in the image. The KIT includes easy-to-understand illustrated instructions in English. LEVEL OF EXPERIENCE REQUIRED medium Assembly and testing by Mectronica STORE is also available by adding quantity 10 of the KIT assembly service which can be purchased by clicking here on EBAY | MECTRONICA STORE and adding it to the cart together with the KIT to be assembled. This original kit allows you to create a mini Tesla coil which, by generating high voltage, creates a small lightning bolt which, for example, allows you to trigger a neon lamp by simply bringing it close to the coil. Power supply: 15 to 24 VDC – 2 A (24 VDC recommended). Technical specifications Power supply: from 15 to 24 VDC Maximum absorbed current: 2 A Generated high voltage: 2.1 kV at 13 Vdc Assembled dimensions (mm): 86x54x65 Components: - R: 47 kohm - C: 100 nF multilayer - Q1: Transistor BD243 - LED: 5 mm LED - L1: piece of wire wrapped around L2 - L2: TESLA coil - BT: DC plug from cs - SW: switch from cs Assembly Start assembling the components starting from the resistor R, from the capacitor C and continuing with the LED, the power plug (BT); then mount the BD243 transistor (Q1) upright and with the metal side facing the outside of the PCB, to which you will then apply the aluminum heat sink. The secondary HT (high voltage) consists of 350 coils of 0.2 mm diameter enamelled copper wire wound (blocked with adhesive tape to prevent them from moving) on a 20 mm cylindrical plastic support approximately 60 mm long. Gently scrape the enamel from the ends with the blade of a knife or scissors (you have removed the enamel when the wire changes colour, becoming more pink than yellowish) in order to remove the insulator and facilitate soldering of the end that goes to the PCB (L2 pad). The other end of the coil, i.e. the one facing up, will remain free. We recommend fixing the base of the TESLA coil to the PCB with Attak type glue. For the primary you have to wind a coil with the 1 mm diameter rigid unipolar electric wire (red wire contained in the kit), directly above the HT secondary. The ends of the primary must then be soldered in the respective areas of the PCB, which are marked L1. The printed circuit, for use, will be placed on a material base insulation, then dry wood or plastic, so that none of its pitches touch metal parts or tops. You can also think of a plastic container from which the upper part of the transformer and the free end of the secondary come out, in order to facilitate the discharge or to be able to connect it to a body from which you want to start the effluvium. Testing Let's get a power supply that supplies a continuous voltage of 15 V at the output, that can deliver a current of 2 amperes and that has a cable ending with a coaxial jack having a diameter suitable for the DC jack socket of the circuit. The polarity of the connector on the board is positive on the central pole and negative on the outer one, therefore the power supply jack must be this way. The remaining free end wire of the secondary must be brought out so that by feeding the circuit it produces a luminous halo due to the corona discharge which causes the ionization of the air and can lead to the consequent production of ozone; the electrostatic effluvium is released from the wire, visible as a cone-shaped halo with very intense light near the wire and faded as it moves away. A characteristic noise similar to a rhythmic breath will be associated with the emission of the discharge; the two phenomena will be more accentuated if the ground of the circuit is connected to an extended metal sheet placed on the support surface of the generator, it being understood that it must remain at least ten centimeters away from the free electrode of the transformer secondary. Approaching a neon light bulb or an energy-saving one (provided it is based on a neon tube) we will see it light up, albeit more weakly than it would light up if it were powered normally: this phenomenon is due to the ionization of the gas contained in the light bulb, by the electric field generated by the transformer. Safety measures ATTENTION ! The circuit works at high voltage and therefore requires the necessary precautions: when it is in operation and in the first few minutes after it is switched off, do not touch the printed circuit board or other components, to avoid getting a shock which for most is only painful but which for a heart patient can be dangerous. Do not place mobile phones, MP3 players and other electronic equipment near the coil, as the coil generates a high-frequency electromagnetic field which may cause interference and damage them. As much as the current that the transformer can release both very low (around a milliampere) the voltage developed is very high and could give a painful shock; getting close to the free end of the secondary and any body connected to it can make it go towards you and this phenomenon could give you a burning sensation. After prolonged use, you must not touch the heat sink of the BD243 transistor, because the temperature it can assume is very high, especially if you power the circuit at 24V. Why mechtronics STORE? Few and simple principles. All products are shipped via the best national couriers such as SDA, GLS, Poste Italiane, BRT and DHL. To facilitate delivery, you will be asked for your telephone number when ordering, allowing the courier to contact you in the event of any problem or eventuality in the delivery. For any delivery needs you can contact us. ALL SHIPMENTS ARE 100% TRACKABLE Not at home during the day? We have the possibility to deliver to the post office near your home or to a Puntoposte! Write the delivery point in the address. PAYMENT Credit cards are also accepted with transactions always made on the secure payment site PayPal. No information about your payment method is shared with us to ensure maximum security. A REGULAR TAX INVOICE IS ISSUED FOR THE PRODUCTS SOLD IF REQUESTED AT THE TIME OF PURCHASE. WITHDRAWAL AND WARRANTY All our products are guaranteed both on delivery and for the duration of use. For products that are defective at the origin we carry out the free replacement of the product. The guarantee has a duration of 2 years for individuals and 1 year for companies/activities. Remember to keep the sales invoice and the original packaging of the product with all the accessories aside! If you are not satisfied with a product, you have 30 days to withdraw from the purchase and receive a refund for the product purchase. TECHNICAL ASSISTANCE What differentiates us from other sellers? We are a company that deals with electronics with technicians dedicated to solving your doubts or problems with our products. No waiting on the phone or call center: you can contact us by phone, whatsapp, email or fax, you can find the references at the bottom of the page. Our experience is at your service to help you choose and use the products on sale. FEEDBACK Your feedback is important to us and to you. Therefore we ask you to report any problems in the sale and to contact us before releasing negative or neutral feedback. Remember to put 5 stars on all fields in the feedback if possible to always guarantee the service we offer. As you can see, the way to contact us is clear and simple, to quickly resolve any problems with our products. ELECTRONICS - DOMOTICS - REMOTE CONTROLS - AUTOMATION AND MECHANICS - SOFTWARE CREATIONS Attention, the product is a KIT and therefore you will receive the components to be welded with a soldering iron for electronics and everything needed to recreate the apparatus as shown in the image. The KIT includes easy-to-understand illustrated instructions in English. LEVEL OF EXPERIENCE REQUIRED medium Assembly and testing by Mectronica STORE is also available by adding quantity 10 of the KIT assembly service which can be purchased by clicking here on EBAY | MECTRONICA STORE and adding it to the cart together with the KIT to be assembled. This original kit allows you to create a mini Tesla coil which, by generating high voltage, creates a small lightning bolt which, for example, allows you to trigger a neon lamp by simply bringing it close to the coil. Power supply: 15 to 24 VDC – 2 A MPN YB677 UPC Non applicabile Marca F.Elettronica EAN Non applicabile

Price: 93.4 USD

Location: Bagno di Piano

End Time: 2024-09-16T12:50:51.000Z

Shipping Cost: 0 USD