EC300 _ 2021 _ Gas Gas _ All Balls _ Rear Suspension Linkage Rebuild Kit

Description: EC300 _ 2021 _ Gas Gas _ All Balls _ Rear Suspension Linkage Rebuild Kit Set of GENUINE All Balls Racing heavy-duty swing arm suspension linkage bearing seal rebuild kit. (Linkage that connects the rear shock to the swingarm underneath the swingarm). Rebuild your swing arm suspension linkage with heavy-duty OEM quality components at only a fraction of the cost. Includes everything you need, including lower shock bearing kit (See pictures list below) Includes linkage arm bearings, shafts, seals,lower shock bearings, and spacers (if needed) Bearing shafts use 52100 bearing steel that is through hardened and precision ground Needle bearings use 52100 bearing steel, the ST13 shell is ARC 61-65 heat treated Bushings are case hardened and plated to prevent wear Comes with everything pictured This kit includes: 6 Bushing 7 Needle Bearings 4 Needle Bearing Shafts 8 Seals 6 Washers Please ensure your model and year are listed below for proper fitment. This part will ONLY work on models and years listed above. Year Model Gas Gas 2021 EC300 2021 EX300 Husqvarna 2014-2020 TC 125 2015-2016 TE 125 2017-2019 TE 150 2020-2022 TE 150i 2014-2021 FC 250 2015 FC 250 (EURO) 2014-2020 FE 250 2014-2020 TC 250 2014-2018 TE 250 2018-2022 TE 250i 2014-2018 TE 300 2019-2020 TE 300i 2022 TE 300i 2017-2019 TX 300 2020 TX 300i 2014-2021 FC 350 2014-2022 FE 350 2015-2016 FE 350s 2020-2022 FE 350s 2017-2020 FX 350 2014-2021 FC 450 2015 FC 450 (EURO) 2018-2019 FC 450 Rockstar Edition 2014 FE 450 2016-2020 FE 450 2018 FS 450 2020 FS 450 2017-2020 FX 450 2014-2022 FE 501 2015-2016 FE 501s 2020-2022 FE 501s Husqvarna 2012-2020 SX 125 2012-2020 SX 150 2012-2014 XC 150 2012-2022 SX 250 2011-2020 SX-F 250 2015 SX-F 250 Factory Edition 2012-2019 XC 250 2020-2022 XC 250 TPI 2011-2020 XC-F 250 2012-2019 XC 300 2020-2022 XC 300 TPI 2011-2020 SX-F 350 2011-2020 XC-F 350 2011-2020 SX-F 450 2015-2016 SX-F 450 Factory Edition 2018-2019 SX-F 450 Factory Edition 2013-2020 XC-F 450 Installation tips:. 1. Before installing the needle bearings make sure the linkage bearing bores are clean and free from burrs. It is also helpful to have the entire linkage clean so that dirt does not get into the bearings. 2. The needle bearings should be installed with a press and a tool that is just a bit smaller than the outer diameter of the needle bearing (a socket often works well for this). A vice may work if no press is available. Never use hammer blows to install the needle bearings. Hammer blows will damage the needle bearings. NOTE: Heating the bearing bore of the swing arm or linkage will make bearing installation easier. 3. Once the bearings are installed, grease them excessively. The more grease the better. 4. When installing the seals, grease the inner seal surface that contacts the mating parts. The grease on the seals helps lubricate the seal as well as making an additional barrier to dirt and water. Refer to your repair manual for proper disassembly and assembly procedures. Always refer to a repair manual for proper tear-down, assembly, and break-in procedures (if applicable). Not sure this is right for your ride? Just click the Contact Seller link near the upper right of the page we'll be happy to help. Not 100% positive of your model year? (It may NOT be the year built) See the last picture for our VIN# / HIN# decoder chart. We are based in Imperial Missouri, but your order will ship from one of the multiple warehouses in the USA (Whichever is closest to you).

Price: 87.26 USD

Location: Imperial, Missouri

End Time: 2024-11-14T20:41:46.000Z

Shipping Cost: 0 USD