4 pc Fabtech HD Tie Rod Assemblies w/ Tool 11-24 Silverado Sierra 2500HD 3500HD

Description: 4 pc Fabtech HD Tie Rod Assemblies w/ Tool 11-24 Silverado Sierra 2500HD 3500HD Fabtech Heavy Duty Tie Rod Assembliesw/ Inner Tie Rod Tool THIS LISTING IS FOR: 1 - FTS71005 - Fabtech HD Tie Rod Assemblies - 4 Pc Set Two Inners and Two Outers 1 - KRY-KRP0083 - Inner Tie Rod Tool Lift kits, Oversized wheels and tires, Off Roading, Drag Racing, Sled Pulling and just everyday driving can apply extreme demands on the stock GM steering components. The factory tie rod assemblies on the New Chevy and GMC - 2500HD / 3500HD Trucks are not sufficient for the job they were asked to do. These components were way under designed from the factory and are a real danger when extra loads are put on them. From the start these undersized components are the weak link in the front end of your truck and need to be addressed for a good reliable solid steering system. Since the factory tie rod ends are not what they should be, they start wearing prematurely which will result in sloppy steering at first, then eventually the worst case, complete failure and breakage. Even the tie rod shaft themselves are very thin and weak, we have seen them bend from just mild off roading or sled pulling. Unfortunately the original units were just way under designed from the get go. So even original size aftermarket replacements parts are not much better, the original OEM design is just too small to take the extra demand put on them. It is the small size of the joint and the main shaft that is the culprit not just the quality of the part..... Quick Story ~~ We have seen first hand GM outer tie rods ends give up the go and break apart, and this was on a truck that had never seen the dirt and was used for normal street driving. Not to scare anyone, but I think I need to share a friends story with you. A good friend and local police officer took his 2001 GMC Sierra with a 8" Fabtech lift on a 300 mile rode trip to the Colorado river. He had the truck loaded with all of the family's stuff for the weekend, then hooked up the family ski boat, loaded his wife and two kids in the truck and left the house for a fun family weekend. After traveling 300+ miles on the interstate he exited the interstate and headed for the vacation house. As he slowly entered the drive way and went up that little tiny 1" bump on the edge of the driveway, the right outer OE tie rod end snapped off and sent the tire flopping rearward into the fender well and stopped him in his tracks. Luckily this is when it decided to break, at low speeds in front of his house, how lucky to have it break then and there, after traveling over 300 miles at highway speeds. Who knows what could have happened if it had broken off at highway speeds???? He NOW owns a set of these tie rod ends!!! These Fabtech Super Tie Rod Assemblies are almost three times the size of the original GM Units. Provide better steering control and increased safety. THEY ARE A MUST FOR LIFTED TRUCKS WITH BIGGER TIRES.Don't get left on the side of the road, buy some insurance and peace of mind. Directly replaces original factory units and attaches to the stock center link. Applications: 2011-2024 - Chevy Silverado 2500 HD & 3500 HD (2 & 4wd) 2011-2024 - GMC Sierra 2500 HD & 3500 HD (2 & 4wd) ~~~~~~~~~~~~~~~~~~~~~~~~~ Does NOT fit Fabtech 6" Lift Kit Does NOT fit 1500 Light Duty Does NOT Fit 2011-2016 - 8 Lug SUV Does NOT fit 2001-2010 HD Trucks Part # FAB-FTS71005/KRY-KRP0083 Powered by SixBit's eCommerce Solution

Price: 344.83 USD

Location: Buena Park, California

End Time: 2024-10-05T00:27:10.000Z

Shipping Cost: 0 USD