3000W Dual MPPT Wind Solar Hybrid Charge Controller Auto 12V 24V 48V Regulator

Description: 3000W Dual MPPT Wind Solar Hybrid Charge Controller 12V 24V 48V Auto Regulator Functions and FeaturesWind generator MPPT boost charging function,improved charge efficiency . External dump load resistant to strong wind,work more stable . Solar MPPT charge，Solar intelligent disconnect charging，high efficiency charge. Bluetooth function can monitor the system information by the app on the app on thephone(Only for Android). Dual power supply function: Battery + solar power supply. LCD displays parameters such as voltage and current of wind, solar andload .Some parameters can be set by users. DC output with 3 output modes. Battery module type can be selected and parameters can be set；The controller has a built-in dust net, which is easy to replace and clean, ensuringthe service life of the controller. The inner circuit board of the controller is sprayed with conformal coating toprevent dust, moisture and static electricity Reversed charging Protection of solar ：Such as at night, the voltage of the battery may be higher than solar panel. The controller protect the battery from charging the solar panel. Reverse polarity Protection of battery：When the battery polarity is reversed, the controller does not work and there is no display. The fuse protects the internal circuit.If the battery does not work properly after it is connected correctly, just need to replace the fuse . Battery open circuit Protection ：After long-term use, the battery may be Open-Circuit or poor connect. The controller can protect itself from damage.Check the connection regularly Over voltage Over current Over load voltage： When it’s strong wind or over voltage, the controller will automatically start braking function to protect the wind generator and battery. The controller will automatically cuts off the circuit when the output is over voltage. Lightning Protection ：Lightning protection refers to the last level of protection necessary for equipment. For lightning-prone areas, special lightning protection devices and other components of the multilevel lightning protection system are needed. It need additional payment If the user need this function. Introduction of the MPPT The Maximum Power Point Tracking (MPPT) system is an advanced charging technology that enables solar panels to output more power by adjusting the working state of electrical modules. Due to the non-linearity of a solar array,there is a maximum energy output point (maximum power point) on the curve of the array. Traditional solar charge controllers (switch charging technology and PWM charging technology) cannot charge batteries at this point, thus unable to obtain the maximum energy of solar panels. However, the solar energy charge controller equipped with the MPPT control technology can track the maximum power point of a solar array at any time in order to gain maximum energy for battery charging.Take the 12V system for example. The peak voltage of solar panels (Vpp) is around 17V and battery voltage is about 12V. Generally, when the solar charge controller is charging a battery, the voltage of solar panel is maintained at about 12V, indicating that the maximum power is not used. MPPT solar charge controllers provide a solution to that problem by constantly adjusting the input voltage and current of solar panels, therefore maximizing input power. Compared with conventional PWM solar charge controllers, MPPT solar charge controllers bring out the maximum power of solar panels and provide greater charging current. Generally speaking, MPPT solar charge controllers can improve energy utilization rate by 15% ~ 20% over PWM solar charge controllers.(Figure 1) Moreover, different environmental temperatures and light conditions lead to frequent changes of the maximum power point. Our MPPT solar charge controller can constantly adjust parameters according to different conditions so as to put the system near the maximum working point all the time. The whole process is completely automatic without any adjustment by users.(Figure 2) The figure is a schematic diagram of the principle of wind turbine MPPT charging. WIND+and WIND - are the DC input terminals of the generator after being rectified by the internal rectifier circuit of the controller. BAT+and BAT - are battery energy storage connection terminals. L1 is the MPPT power inductor, which is used to store energy during the MPPT charging process. D1 is a reverse isolation protection diode that can reduce the loss caused by the conduction of the switch. Q1 is a switching MOSFET, which is the core component of the MPPT circuit. It controls the operation of the MOSFET through a high-frequency PWM drive waveform, thereby adjusting the fan to the maximum power operation state. Due to the constant changes in the wind speed and direction of the natural wind, timely tracking and adjustment are required. According to the generator input signal sampled by the controller, the circuit adjusts the driving waveform of MOS tube Q1 in real time through MCU analysis and control and MPPT software algorithm, thereby achieving instant response and achieving MPPT charging effect The ordinary wind turbine charging controller can only be charged when the fan is large and the fan voltage is higher than the battery voltage. The MPPT controller of this product can not only meet this requirement, but also realize the breeze charging function by boosting the lower fan input voltage through the MPPT boost circuit when the wind force is low and the fan input voltage is lower than the battery voltage, and allowing the fan to operate at the maximum power point. Rated system voltage 12V、24V、48V、12/24 ATUO、24/48V AUTO（ONE OF FIVE） Rated wind power 600W/12V,800W/24V,1000W/48V Rated PV power 1000W/12V,1500W/24V,2000W/48V Charge way for Wind turbine Mppt boost &PWM Charge way for PV MPPT&PWM Max input voltage for wind 12/24V system：wind≤80V ；48V system：wind≤130V Max input voltage for solar 12/24V system：solar≤80V；48V system：solar≤130V Dump load way External dump load ，wind power ≤1KW with R1，wind power ≥1KW with R2 No-load Current (DC) ≤0.06A Controller power mode Battery or solar panel Communication Bluetooth（need to purchase） Output load working mode(Mode) Mode 1: Light-control on. Light-control off (3 modes adjustable) Display LCD display (clear and easy to understand ) Display content LCD display,Voltage, Percentage of battery power, Current, working mode of load, etc Protection Solar Reversed Charging protection，Battery open circuit protection、battery anti-reverse connection protection protection、Over current and over voltage auto brake protection、Over load protection,etc. Cooling mode Cooling fan and self-cooling Workingtemperature/ Relative humidity ﹣20~﹢55℃/35~85%RH (non-condensing) N W. 2.85Kg GW.(Controller+dumpload） 4.9Kg NW. For R1，R2 R1：0.95Kg 、R2：1.35Kg Size for Controller /Package Size 260*194*97.33mm / 390*320*155mm Dump load size ： R1：210*70*130mm、R2：200*90*150mm PaymentDelivery detailsReturn PolicyAbout usContact us Payment We accept eBay payment. Please do not email us to ask for other payment option. We appreciate prompt payment and look forward to your business in the future. Unpaid item will be filed without receiving payment in 7 days from listing ended. Delivery details Usually we ship your order out within 3-5 business day.For shipping and handling charges (S&H) for specific item, please refer to the item listing page for more details.Please make sure your shipping address is correct. We are not responsible for any loss in transit if a wrong address is provided. Return Policy Returns for exchange are permitted and must be initiated by the buyer within 30 days upon receipt. If you would like to return your product(s) for repair / replacement / refund, please kindly contact our customer service representatives via email for an authorized RMA number. Your returned product(s) will not be processed without a completed RMA. About us We are continually expanding our product selection to better serve your need. We look forward to providing the best sevice to you - our dear customers, so take a look around our store and find the product that you want. You can put your trust in us! If you need any help or have any suggestions, please don't hesititate to contact us anytime , we will reply you within 24 hours and try the best to help you. Contact us Welcome to our shop! Your satisfaction is our top priority. Please do not hesitate to contact us if you have any questions about our products or services. Thank you very much!Our working hours (Monday to Friday):-09:00-12:00 (GMT+8)-14:00-18:00 (GMT+8)Saturday:-09:00-12:00 (GMT+8)-14:00-17:00 (GMT+8)All emails are answered very quickly during our working hours, emails are usually answered within 24-hours during the holiday.Welcome to contact us if you have any problem.

Price: 229.99 USD

Location: Wuxi

End Time: 2025-01-01T02:49:47.000Z

Shipping Cost: 0 USD