3000W 220V 50HZ Watercuring Grouting Machine Acrylate Perfusion Plugging Machine

Description: Product Description High-pressure 3000W 220V/50HZ Two-component Water-curing Grouting Machine Acrylate Material Acrylate Perfusion Plugging Machine Drive motor power: 3000W Restart pressur: 13000PSI Safety pressure range: 0~8000PSI Voltage/frequency: 220V/50HZ Maximum particle size: 0~2MM Net weight: 17KG Product name: two-component water-curing grouting machine Acrylic brine solidified two-liquid grouting machine is a new type of high pressure grouting equipment. The inside and outside of the product are made of special tough and wear-resistant materials, which make it durable and durable, and eliminate the disadvantages of insufficient pressure of the traditional water-curing equipment, easy internal blockage and poor corrosion. The fuselage has two special inlet and outlet valves for sucking in and discharging materials. The material of the product is a high-molecular polymer with water as a dispersion medium. The material does not increase the viscosity of water after being dissolved in water. Under the pressure of the grouting equipment, it can quickly penetrate into all water-permeable gaps and occur instantaneously. Curing reaction. Forms an acid and alkali resistant; corrosion resistant, highly flexible 100% impervious gel. The underground concrete is glued together to further fill all the leaking gaps. Thereby achieving the purpose of plugging and leaking. Product advantages: 1. It can absorb the water in the leak when curing, which is very suitable for water plugging. 2. Self-curing requires no external materials, and the curing time can be adjusted according to the situation. The curing time can be controlled between 3s and 90min, depending on the situation. 3. The cured colloid has high flexibility and effectively solves the structural expansion problem. 4. Because it has no viscosity; the concentration is the same as water, so it can penetrate all the gaps that water can penetrate. The penetration range can reach 3-5 square meters under the pressure of the grouting equipment. It makes up for the defects that the traditional grouting liquid has high viscosity and cannot penetrate into the fine gap, so it does not need to be over-tightened. 5. It has good chemical resistance to most acids and bases and is not affected by biological damage. The scope of application: 1. Waterproof plugging and seepage prevention works for cracks in family toilets, swimming pools, external walls, basements, garage roofs, elevator shafts, tunnels, bridges, subways, dams, harbors, and civil air defense projects. 2. Fill the dry and wet cracks on the concrete structure of the basement, interior and exterior walls, structural honeycombs, bricks, etc. of the building, and actually cover all the contact surfaces. Fourth, water curing ingredients: 1. Component A is the main agent, 4KG group A is diluted with water 20KG, component B is curing agent, and each 0.5KG group B is diluted with 20KG of water and stirred until completely dissolved. 2. After the dissolution is completed, take AB 1:1 equal amount and test the curing time. In general, the curing time is preferably 3-5 minutes. 3. When the water is blocked, reduce the amount of water added so that it absorbs the water in the leak. 4. The more the same amount of water is added to the A group, the stronger the colloidal strength after curing becomes more brittle. The more the amount of water B added in the same amount, the shorter the solidification time. construction method: 1. Drill holes in the leaking part. 2. According to the actual situation, the pre-embedded tube (12mm/10mm/8mm/6mm) is pre-buried in the hole and left outside for 20 cm. 3. Secure the pre-embedded pipe with watertight seal. 4. After all the pre-buried OK, start the grouting equipment, connect the AB-integrated discharge port to the quick-reading joint of the pre-embedded pipe, start the manual control and start grouting. 5. According to the structure, the pressure can be appropriately increased or decreased to ensure that the slurry penetrates into the finest gap of the structure. If there is slurry leakage on the surface of the grout during the grouting process, the grouting operation should be stopped immediately, and the leaking point should be closed by appropriate methods, and then the grouting operation should be continued. If the pre-embedded pipe is clogged, the PU pipe can be drilled or replaced.

Price: 1100 USD

Location: Changsha

End Time: 2024-08-09T04:01:43.000Z

Shipping Cost: 0 USD