20GPM 12V Red Fuel Transfer Pump w/ Discharge Hose & Manual Nozzle + Flow Meter

Description: Package List 1*20GPM 12V Red Fuel Transfer Pump with Discharge Hose & Manual Nozzle + Fuel Flow Meter (As Pics Shown) Description 【Multi-function】- 20GPM 12V Red Fuel Transfer Pump for Transfer of Gasoline, Diesel Fuel, Kerosene, Mineral Spirits, Heptane, Hexane, E15, Biodiesel, and Similar Fuels or Oils. Suitable for lawn tractors, boats, motor boats, snowmobiles and trimmers, etc. 【High Capacity】- This industry standard DC pump dispenses up to 20 GPM, which could make fueling be more efficient. Designed for 12V battery powered bung mounted transferring from fuel tanks on trailers or trucks, this transfer pump will pull fuel at tank depths of 8 ft. and discharge fuel up to heights of 37 ft. 【Good Quality】- This Fuel Transfer Pump body is made of cast iron, which is sturdy and durable. The pump body adopts a waterproof design, and the pump has a built-in filter and a bypass valve. Package include Discharge Hose & Manual Nozzle & Fuel Flow Meter. 【Easy Installation】- Come with 1"Mechanical Fuel Flow Meter 4-Digital Batch Display OE# FM-120-2 for All Gasoline Kerosene Diesel Fuel Transfer Pump. Made in quality materials, and we tested each one before shipping, so easy to install. 【Dependable & Durable Pump】- For the design of ball bearing, no lubrication is required in our gasoline pump. Made with durable cast iron construction to withstand rough operating environments, We provide 1 year warranty on the Fuel Transfer Pump. 【Attention】- 1. Please make sure the wired motor is fully charged before use for better work (if the power is too low, the product may not be able to reach the normal working efficiency) ; 2. If your pump stops working during use, this may be due to the motor overheating and triggering the protection mechanism, please make sure that the wired motor is fully charged, and then try to restart it after 15 minutes of cooling. Advantages of rotary vane technology Increased suction lift No performance loss due to vane wear Self-priming ability Easy maintenance Consistent performance Attention To achieve maximum suction lift, the inlet plumbing should be as straight as possible with no elbows or bends in the line. Accessories, such as filters, should not be installed on the inlet side of the pump. Valves should be set with minimum spring pressure and must contain a pressure relief valve. Variables that increase discharge pressure/decrease flow-rate: Adding accessories (filters, measuring devices, swivels, etc…) Changing accessories (increasing the length or decreasing diameter of hose) Dispensing fuel above the pump (the higher the discharge point is above the pump the lower flow-rate) Pumping higher viscosity fluids (umps are designed to pump at a viscosity no greater than kerosene) Product Details Padlocking Manual Nozzle Kit Move Switch Fuel Flow Meter Safety Information WARNING! Electrical wiring should be performed ONLY by a licensed electrician in compliance with local, state, and national electrical code NEC/ANSI/ NFPA 70, NFPA 30, and NFPA 30A, as appropriate to the intended use of the pump. Threaded rigid conduit, sealed fittings, and conductor seal should be used where applicable. The pump must be properly grounded. Improper installation or use of this pump can result in serious bodily injury, or death! WARNING! To ensure safe and proper operation of your equipment, it is critical to read and adhere to all of the following safety warnings and precautions. Improper installation or use of this product can cause serious bodily injury or death! NEVER smoke near the pump, or use the pump near open flames when pumping a flammable liquid! Fire can result! A filter should be used on the pump outlet to ensure no foreign material is transferred to the fuel tank. Threaded pipe joints and connections must be sealed with the appropriate sealant or sealant tape to minimize the possibility of leaks. Storage tanks must be securely anchored to prevent shifting or tipping when full or empty. To minimize static electricity build up, use only static wire conductive hose when pumping flammable fluids, and keep the fill nozzle in contact with the container being filled during the filling process. The pump motor is equipped with thermal overload protection; if overheated, the motor will shut off to prevent damage to the windings. WARNING! This product shall not be used to transfer fluids into any type of aircraft. WARNING! This product is not suited for use with fluids intended for human consumption or fluids containing water. On May 23, 2024 at 20:13:12 PDT, seller added the following information:

Price: 211.99 USD

Location: Chino, California

End Time: 2024-10-24T03:06:10.000Z

Shipping Cost: 0 USD