1948-52 Fits Ford Truck IFS Crossmember, Fits Mustang II Suspension, Deluxe

Description: This IFS crossmember is a great way to improve your vehicles suspension, handling, and overall performance, Works with both manual and power rack and pinions, Frame Front Boxing Plates are available for added strength/support (91054430), Requires the use of tubular no-strut style lower control arms, Choose from a variety of front suspension kits to finish off your front end 1948-52 Ford Truck IFS Crossmember, Mustang II Suspension, Deluxe Sku # 91034430-DLX Mfr. Part # 91034430-DLX Condition New Brand Speedway Motors Sold Set Details Info Vastly improved handling when compared to original straight axle setups Front steer rack-and-pinion steering provides greater steering feel Complete weld-in assembly made from 3/16-inch steel adds strength Vertical inner uprights provide a strong design with twice the weld area Application specific crossmember and spring towers pre-welded to save installation time Allows for numerous control arm and disc brake kit upgrade options Compatible with manual and power rack-and-pinion steering systems Compatible with stock stamped steel control arms as well as tubular control arms Stock style control arms will require strut rod brackets or tubular strut rod kit Rack-and-pinion mounting points rotated rearward 20 degrees for steering shaft clearance Built-in anti-dive and bump steer correction mounting points Lower control arm pivot tubes and corner gussets not included Accepts stock Mustang II spindles or aftermarket drop spindles All welds ground smooth on Deluxe model, saving you time and energy during installation Drastically Improve Your ’48-’52 Ford Truck’s Handling with A Mustang II IFS Crossmember Much like the advent of hydraulic, or “juice” brakes, became an industry standard, so has independent front suspension (IFS). You’ll find IFS on just about every production car and light duty truck sold in America due to its inherent improvement in ride quality, handling, and the ability to provide better control at higher road speeds. These updates are what can turn a long drive at highway speed in your ’48-’52 Ford truck from sketchy to serene simply by updating the original style straight axle suspension for a well-engineered weld-in IFS solution utilizing the tried and true suspension geometry that debuted on the 1974 Mustang II. Built Strong to Handle the Road Ahead and Look Good Doing It The typical straight axle front suspension limits you to maybe 2-1/2-inches of suspension travel. That’s not much, which means you’re in for a rough ride. On top of that you’re limited in leaf spring rate choices and the steering linkage setup with bushed kingpins creates some hair raising steering feel, or lack thereof, when you get up to highway speed. Of course, there is always the effect of alignment on a front suspension and getting a straight axle front end aligned is no small chore, often requiring heating/bending of the axle tube itself or other modifications. Converting your ’48-’52 Ford truck’s chassis to the Mustang II front suspension design with our crossmember kit brings you a whole different driving experience, one that will have you looking for any excuse to get out on the open road and take long trips to events you never attended before due to your Ford’s poor handling at modern highway speeds. Beginning with our 7 gauge steel (that’s a full 3/16 of an inch thick) boxed Mustang 2 front suspension crossmember that is fully welded with extended vertical uprights we have designed in anti-dive geometry to our crossmember and spring towers. Suspension travel, which yields a better ride, is upwards of five inches with our IFS and aligning the IFS can be handled easily by any competent alignment shop. Rack-and-pinion steering provides a quick and crisp steering effort at any road speed, and we have designed our rack mounting tabs to not only be optimized to eliminate bump steer but lay the steering rack back at a 20 degree angle to facilitate a lower steering shaft angle. This helps with exhaust manifold/header and overall engine clearance. The mounts accept both 15-1/2-inch and 16-inch on center rack mount spacing. Lastly, upgrading to a weld-in IFS Mustang 2 front end kit greatly enhances your braking options with the ability to run the most basic disc brake package all the way up to serious multi-piston racing disc brakes. Track width is dependent upon the brake package and control arms you choose, usually creating a 60- 62-inch hub-to-hub IFS width with stock arm length. We do offer 5/8-inch narrower and control arms if needed for specific wheel placement in your application. Additionally, due to the wider truck frame dimensions, are necessary. As you can see, our crossmember is the perfect foundation for building the best Mustang II front suspension for your ’48-’52 Ford truck. Welds to Your Stock Frame Rails for Strength and Accuracy We understand that bolt-in suspension upgrades are easier for those that like to spin their own wrenches, but we designed our Mustang II crossmembers to be a weld-in solution to maintain their strength and integrity throughout the life of your ’48-’52 Ford truck. While we do encourage the use of a certified welder or chassis shop for installation, if you know your way around a measuring tape and have a MIG welder in your garage there’s really nothing stopping you from following our detailed instructions to fit and weld our Mustang II front suspension crossmember into your ’48-’52 Ford’s frame rails. Welding our Mustang II suspension crossmember into place is a straightforward installation and can be handled in just a few short hours once the old straight axle and front suspension have been removed. Our economy crossmember can use stock-style lower Mustang 2 control arms or tubular style arms, but you will need or our for installation. Deluxe crossmembers work with tubular-style lower control arms only. Note, lower control arm pivot tubes and gussets are not included, as they are typically included with tubular style lower control arm kits. We offer with and without disc brakes to help you complete your installation. We highly recommend our ’48-’52 for increased frame support and strength as well. Lastly, if using a power rack-and-pinion steering unit you will need our for proper clearance along with the corresponding . Charts (PDF) Installation Tips Drop: This varies and is dependent on application and options. Most kits drop the vehicle by 3-4". Drop spindles and running lower profile tires than stock also adds to the amount of drop that can be achieved. You can also fine tune your ride height with our Mustang II . Track Width: You may want to mount custom wheels to your Mustang II conversion and determining proper track width for your application is essential for figuring correct backspacing and overall ride stance. Standard wheel base is 56-1/2" with a 60" version available for trucks. Narrowed arms are available to move the wheel in by 5/8" on each side. See our PDF for various track width options. Assembly Notes: Either manual or power steering can be used with these crossmembers. The passenger side mount has a slot that will take the later model power rack. With all Mustang II aftermarket crossmembers, and must be used with the later (Fox-body) power rack. Engine Mounts: We offer for most popular V8 engines, including SBC, LS, SBF, and early Hemi. Note: Applications where the vehicle has fenders that mount directly on top of the frame, the fenders will require extensive modification to allow clearance for the upper cross member section. Specs Material Type Steel Sold in Quantity Kit Finish Natural Notes Includes crossmember and shock cups. Material Thickness 0.18 Position Front Attachment Style Weld-on Crossmember Type Mustang II Crossmember Style Boxed Steering System Compatibility Manual/Power Rack and Pinion Control Arm Compatibility Tubular | Strutless Material Gauge 7-gauge Ride Height (w/Stock Spindles) 3" to 4" Lowered Tie Rod Extensions Required Yes MFG. Part # 91034430-DLX Reviews Smart buy. Rated by Lance on February 02, 2022 Summary: Easy to level and install, ready to be welded. Yes, I recommend this product. Great quality craftsmanship fits perfectly Rated by 51 ford on January 22, 2021 Summary: Great products and great prices Yes, I recommend this product. The product looks great. Very well built. Rated by none on June 18, 2020 Summary: I like that I is custom fit to my vehicle. There is no alteration to be done. Yes, I recommend this product. Fit good looks good Rated by Keith on June 05, 2020 Summary: Good unit Yes, I recommend this product. I would definitely recommend this cross member to everyone. Rated by Eli, "The Missing Link" Rivas on May 12, 2020 Summary: I am currently building a 1948 Ford F1 from the ground up. This front cross member is exactly what my frame needed. Great looks, superbly constructed...great looking welds, and most importantly...clear and concisely written and diagrammed instructions for a fool-proof install. Pros: Great design. Excellent material of construction Yes, I recommend this product. Related Items / Suggested Parts Mustang II IFS, Standard Tubular Control Arms, Stock Springs and Spindles Mustang II IFS, Std. Tubular A-Arms, Coilover Springs, Stock Spindles Mustang II IFS, Std. Control Arms, Air Ride, Dropped Spindles, Wilwood Brakes Mustang II IFS, Narrow Arms, Air Ride, Dropped Spindles, Wilwood Brakes Mustang II Tubular Lower Arms for Air Ride/Wilwood Brakes No Strut Rod Mustang II Tubular Lower Arms, Air Ride/Wilwood, No Strut, 5/8 In 1948-1952 Ford Pickup Front Frame Boxing Plates Inner Tie Rod Extention Kit - Speedway Mustang II Manual Rack Speedway Mustang II/T-Bird 2 Inner Tie Rod Extension, Power Version Tech Support We're here to help before and after your purchase. If you have a question or need assistance with one of our products, please contact us through eBay Messaging and a knowledgeable Speedway Motors team member will be happy to help. About Speedway Motors is America’s Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 72 years. Founded in 1952 by “Speedy” Bill Smith – a racer and street rodder himself – Speedway has grown from a one-man operation to become the world’s largest manufacturer, distributor and retailer of street rod and racing products. Our industry-leading fast delivery is the result of same-day shipping from our state-of-the-art, centrally located 500,000 sq. ft. headquarters. Speedway’s size offers customers unmatched product selection and low pricing, while our excellent technical support and customer service have made us a recognized leader in the rodding and racing industries.

Price: 353.99 USD

Location: Lincoln, Nebraska

End Time: 2024-12-10T13:08:19.000Z

Shipping Cost: 0 USD