Description: RESIN2detailHigh QualityFree ShippingCustomer Support1/48 FAST FIX P-36 Hawk Resin Cowl + Engine Upgrade RESIN2detail 48221 1/48 FAST FIX P-36 Hawk Resin Cowl + Engine Upgrade RESIN2detail 48221 One-piece resin cowl with gun blisters, ventral intake and open vents. Realistic scale thickness and flap detail. No need to fill center-line seam with this set. Bundled with our super-detailed R-1830 Fast Fix engine front which is drop-fit Designed to fit Wolfpack / Academy Kits *********************************************************************************************************************************************************************** NOTE(S): This is an ADVANCED kitset. Prior experience using 3D printed resin parts HIGHLY recommended. Will take between15 and 20 minutes for an experienced modeller to carefully remove supports. Remember -- Go slow and take your time - the resin can be brittle! Parts are thin and can plit/crack easily. Recommended tools: Flush-cut trimmers, Tamiya Razor Saw (or similar) and sharp #11 hobby knife. INSTRUCTIONS: Recommended Steps to remove supports: 1) Start with outer supports ring. a) Use a NEW #11 hobby knife blade to slice the supports about 0.5mm from where it attaches to the part/cowl flap trailing edge. You do not want to apply too much pressure here or it may chip the thin section. Start with the section closest to the base and work your way slowly around. It might take 5-10 gentle slices to free it from the part. Take your time here! b) Use Xuron flush cut trimmers to break off the stems from the supports detached from part in step 1(a) c) Use razor saw (use water here to lubricate blade and cut down on dust) to carefully cut all support stems from the base 2) Once cowl fully detached from base, use Xuron or Sharp #11 blade to carefully detache the inner support ring which attaches to the inside edge of the cowl opening. Remove with tweezers or shake parts into trash. 3) Remove remaining attachment stubs from part carefully using either #11 blade or flush-cut Xuron trimmers 4) Wet-sand remaining attachment points to slowly grind them down flush / flat 5) Careully clean in soapy water and move on to Engine using same general idea from a support removal perspective Recommended for modelers 17+ and/or those with experience installing aftermarket aircraft upgrades. Prior modelling experience highly recommended. As with all resin products, keep dust to a minimum and use water if/when it is sanded. ************************************************************************************************************************************************************************ Scale: 1/48 Brand: RESIN2detail Condition: Brand New Shipping: Free USPS First Class Shipping included SKU: R2D48221 Please check out our other scale model and accessory eBay listings!Choose from a Huge Selection of Top-Quality Model Kits and Accessory Brands! PaymentShippingReturnsPaymentShippingReturns We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! We offer FREE shipping on Most orders! Your order will be dispatched within 1 working day of receiving payment (Monday-Friday) and you should expect to receive it three to five days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement. If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 30 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. High QualityFree ShippingCustomer Support1/48 FAST FIX P-36 Hawk Resin Cowl + Engine Upgrade RESIN2detail 48221 One-piece resin cowl with gun blisters, ventral intake and open vents. Realistic scale thickness and flap detail. No need to fill center-line seam with this set. Bundled with our super-detailed R-1830 Fast Fix engine front which is drop-fit Designed to fit Wolfpack / Academy Kits *********************************************************************************************************************************************************************** NOTE(S): This is an ADVANCED kitset. Prior experience using 3D printed resin parts HIGHLY recommended. Will take between15 and 20 minutes for an experienced modeller to carefully remove supports. ---Remember -- Go slow and take your time - the resin can be brittle! ---Parts are thin and can plit/crack easily. ---Recommended tools: Flush-cut trimmers, Tamiya Razor Saw (or similar) and sharp #11 hobby knife. INSTRUCTIONS: ---Recommended Steps to remove supports: 1) Start with outer supports ring. a) Use a NEW #11 hobby knife blade to slice the supports about 0.5mm from where it attaches to the part/cowl flap trailing edge. You do not want to apply too much pressure here or it may chip the thin section. Start with the section closest to the base and work your way slowly around. It might take 5-10 gentle slices to free it from the part. Take your time here! b) Use Xuron flush cut trimmers to break off the stems from the supports detached from part in step 1(a) c) Use razor saw (use water here to lubricate blade and cut down on dust) to carefully cut all support stems from the base 2) Once cowl fully detached from base, use Xuron or Sharp #11 blade to carefully detache the inner support ring which attaches to the inside edge of the cowl opening. Remove with tweezers or shake parts into trash. 3) Remove remaining attachment stubs from part carefully using either #11 blade or flush-cut Xuron trimmers 4) Wet-sand remaining attachment points to slowly grind them down flush / flat 5) Careully clean in soapy water and move on to Engine using same general idea from a support removal perspective Recommended for modelers 17+ and/or those with experience installing aftermarket aircraft upgrades. Prior modelling experience highly recommended. As with all resin products, keep dust to a minimum and use water if/when it is sanded. ************************************************************************************************************************************************************************ Scale: 1/48 Brand: RESIN2detail Condition: Brand New Shipping: Free USPS First Class Shipping included SKU: R2D48221 Please check out our other scale model and accessory eBay listings! RESIN2detail1/48 FAST FIX P-36 Hawk Resin Cowl + Engine Upgrade RESIN2detail 48221 1/48 FAST FIX P-36 Hawk Resin Cowl + Engine Upgrade RESIN2detail 48221 One-piece resin cowl with gun blisters, ventral intake and open vents. Realistic scale thickness and flap detail. No need to fill center-line seam with this set. Bundled with our super-detailed R-1830 Fast Fix engine front which is drop-fit Designed to fit Wolfpack / Academy Kits *********************************************************************************************************************************************************************** NOTE(S): This is an ADVANCED kitset. Prior experience using 3D printed resin parts HIGHLY recommended. Will take between15 and 20 minutes for an experienced modeller to carefully remove supports. Remember -- Go slow and take your time - the resin can be brittle! Parts are thin and can plit/crack easily. Recommended tools: Flush-cut trimmers, Tamiya Razor Saw (or similar) and sharp #11 hobby knife. INSTRUCTIONS: Recommended Steps to remove supports: 1) Start with outer supports ring. a) Use a NEW #11 hobby knife blade to slice the supports about 0.5mm from where it attaches to the part/cowl flap trailing edge. You do not want to apply too much pressure here or it may chip the thin section. Start with the section closest to the base and work your way slowly around. It might take 5-10 gentle slices to free it from the part. Take your time here! b) Use Xuron flush cut trimmers to break off the stems from the supports detached from part in step 1(a) c) Use razor saw (use water here to lubricate blade and cut down on dust) to carefully cut all support stems from the base 2) Once cowl fully detached from base, use Xuron or Sharp #11 blade to carefully detache the inner support ring which attaches to the inside edge of the cowl opening. Remove with tweezers or shake parts into trash. 3) Remove remaining attachment stubs from part carefully using either #11 blade or flush-cut Xuron trimmers 4) Wet-sand remaining attachment points to slowly grind them down flush / flat 5) Careully clean in soapy water and move on to Engine using same general idea from a support removal perspective Recommended for modelers 17+ and/or those with experience installing aftermarket aircraft upgrades. Prior modelling experience highly recommended. As with all resin products, keep dust to a minimum and use water if/when it is sanded. ************************************************************************************************************************************************************************ Scale: 1/48 Brand: RESIN2detail Condition: Brand New Shipping: Free USPS First Class Shipping included SKU: R2D48221 Please check out our other scale model and accessory eBay listings!Choose from a Huge Selection of Top-Quality Model Kits and Accessory Brands! Payment We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! Shipping We offer FREE shipping on Most orders! Your order will be dispatched within 1 working day of receiving payment (Monday-Friday) and you should expect to receive it three to five days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.Returns If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 30 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. High QualityFree ShippingCustomer Support 1/48 FAST FIX P-36 Hawk Resin Cowl + Engine Upgrade RESIN2detail 48221 One-piece resin cowl with gun blisters, ventral intake and open vents. Realistic scale thickness and flap detail. No need to fill center-line seam with this set. Bundled with our super-detailed R-1830 Fast Fix engine front which is drop-fit Designed to fit Wolfpack / Academy Kits *********************************************************************************************************************************************************************** NOTE(S): This is an ADVANCED kitset. Prior experience using 3D printed resin parts HIGHLY recommended. Will take between15 and 20 minutes for an experienced modeller to carefully remove supports. Remember -- Go slow and take your time - the resin can be brittle! Parts are thin and can plit/crack easily. Recommended tools: Flush-cut trimmers, Tamiya Razor Saw (or similar) and sharp #11 hobby knife. INSTRUCTIONS: Recommended Steps to remove supports: 1) Start with outer supports ring. a) Use a NEW #11 hobby knife blade to slice the supports about 0.5mm from where it attaches to the part/cowl flap trailing edge. You do not want to apply too much pressure here or it may chip the thin section. Start with the section closest to the base and work your way slowly around. It might take 5-10 gentle slices to free it from the part. Take your time here! b) Use Xuron flush cut trimmers to break off the stems from the supports detached from part in step 1(a) c) Use razor saw (use water here to lubricate blade and cut down on dust) to carefully cut all support stems from the base 2) Once cowl fully detached from base, use Xuron or Sharp #11 blade to carefully detache the inner support ring which attaches to the inside edge of the cowl opening. Remove with tweezers or shake parts into trash. 3) Remove remaining attachment stubs from part carefully using either #11 blade or flush-cut Xuron trimmers 4) Wet-sand remaining attachment points to slowly grind them down flush / flat 5) Careully clean in soapy water and move on to Engine using same general idea from a support removal perspective Recommended for modelers 17+ and/or those with experience installing aftermarket aircraft upgrades. Prior modelling experience highly recommended. As with all resin products, keep dust to a minimum and use water if/when it is sanded. ************************************************************************************************************************************************************************ Scale: 1/48 Brand: RESIN2detail Condition: Brand New Shipping: Free USPS First Class Shipping included SKU: R2D48221 Please check out our other scale model and accessory eBay listings!
Price: 32.99 USD
Location: Hackettstown, New Jersey
End Time: 2024-09-14T01:03:23.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
All returns accepted: ReturnsNotAccepted
Return policy details:
Unit of Sale: Single Unit
Custom Bundle: No
Material: Resin
Scale: 1:48
Year Manufactured: 2022
MPN: 48221
Set Includes: Aircraft
Age Level: 17 Years & Up
Vintage: No
Brand: Brian Watkins
Type: Airplane
Year: 2022
Model: FAST FIX
Theme: Militaria
Features: Kit
Country/Region of Manufacture: United States
Item Weight: Hackettstown